What type and brand of grain mill do ya'll have?

[PAian]

Was wondering I am shopping around and wondered what type of mills yall have on hand. Stone gets chugged up from what I've read if you put beans or any legume in it , so I was leaning toward the other varieties

[Christian for Israel]

i don't have one yet. that said, there's an excellent series of articles on them at http://www.waltonfeed.com

the articles on grainmills are here: http://waltonfeed.com/self/grinders.html

here's a bit from the site:

[snip]
The Controversy - Stones VS Burrs:
Stones used to be made from natural rock but now are synthetically manufactured. Good burrs are made from hardened steel. You won't find much controversy over burrs but you will concerning stones.
Stones: I like a stone grinder because it will give a finer grind than burr grinders. Modern grinder stones are made from aluminum oxide. This includes the stones in the Little Ark, the Nugget and the electric Golden Grain Grinder. In my opinion, stones get a very bad rap for two reasons.

Grit In The Flour: The American Dental Association has made a statement that's often repeated by numerous dentists, "You shouldn't use stone ground flour because the grit the stones leave in the flour will wear your teeth down." This might be true of stone ground flour in the third world where native populations use two rocks to grind their meal, but it is not true of these modern grinders. Aluminum oxide stones are Extremely Hard. After the break in period, these stones just don't wear down. I'm told stories all the time by people who have motorized their manual grinders and from people who own electric grinders with aluminum oxide stones. They have individually put tons of wheat through their grinders over many years and their stones are still serviceable. My mom's just one example. Forty years ago when I was a little kid, she got what is now called the Golden Grain Grinder and has used it every week for making bread since then. The stones are still like new. Through all my growing years of eating her bread, I have never felt one piece of grit between my teeth.
I expect there have been people pull their Little Ark or Nugget grinder out of the box, push the directions aside and grind up a cup of flour. Then they never use their grinder again because they found grit in the flour from this first grind. Both of these grinders need to be broken in by putting at least a quart of wheat through them, then discard the flour. After the stones are broken in, that's the end of the grit.
Health Concerns About The Stones' Composition; Aluminum Oxide: There's a hot debate today concerning the effects of aluminum on our health. The U.S. Government doesn't believe that aluminum can be absorbed by our digestive systems. Many of us literally eat aluminum every day as some baking powders are 1/3 alum, a form of aluminum. And many people use aluminum pots. There is valid reason for concern, however, as high amounts of aluminum have been found during autopsies of Alzheimer victims.
I've seen several people choose not to buy one of these grinders because of the aluminum oxide stones. But there's a world of difference between aluminum and aluminum oxide. From the beginning to the end of the manufacturing process, aluminum has never been involved in making the stones. When these stones are made, the manufacturer starts out with the same material that aluminum is made from, bauxite. Bauxite is a red clay that's dug out of the earth. Then it's heated up to over 2,000 degrees C for several days until all that's left is a cinder. This is what the stones are made from. There is no aluminum in them. The aluminum oxide is as harmless as sand and if a particle does break off the stone it will pass harmlessly through you. See Treibacher Schleifmittel's web page for more information on how aluminum oxide is made. The making of aluminum goes through a completely different process, the end result not being at all the same.
The bottom line is you will have to make up your own minds about this issue and go with a burr or impact grinder if you still feel aluminum oxide poses a health risk to you.
Cost VS Use: You may wish to temper your decision on the quality of grinder you will be spending your hard earned cash on by how much you think you will be using it. There's got to be tons of people out there who have a manual grinder, have never used it, and depending on circumstances, never will use it. Contrast this with the families who use a grinder every week to make bread, pancakes, rolls and other things with freshly ground flour. Do you want a manual grinder that will only be used to get you through the tough scrapes or will you be using it all the time? Some people want the very best grinder made whether they are going to use it a lot or not. Other people will purchase the least expensive grinder they can find then learn it won't meet their needs after they begin to frequently use it. Perhaps some real thought should be put into getting a grinder that will nicely serve the expected needs of your family whatever they may be.

[site59]

I have always heared that steel mills are prefered over the plastic ones.
And also that the hopper capacity is important. Bigger the better.
Hope it helps

[jaded]

I have the Nutrimill electric grain grinder. Not cheap at $259, but it makes quick work of grain, and gives multiple options of degree of fineness.

[FarmBoy]

I have the Family Grain Mill until I can afford to upgrade to the Country Living mill. So far, so good.

[happach]

I bought a back to basics gringer years ago. Stainless, still performs well. All manual control. Its a small job grinding in manual. But if you want to eat....... Grinder is small, grinds a cup per load in the hopper. It can be carried in your pack. Sets up on the table with a screw plate.